How the #@%& do you get the fork cap off the 77 CR 125 ? It has a cap that will push down about 1/4 in to barely expose a spring clip that has no bend or resess to get an awl behind it. I can not hold down the cap with one hand and try to work under the clip. A tool like the CZ clutch pin tool would help with the leverage. Anyone have the proper technique or do I have to break down and ask my wife to hold it down?

Share

Reply to This

Replies to This Discussion

Ask her Paul!! My kids are experts at pulling the retaining rings while I compress the springs on an old set of Curnutts that need reservicing almost every time I ride them.

Reply to This

Just like in the 70's Disco era:

It takes two, baby, it takes twoooo....

Reply to This

an awl is too fat. you have to use a pick. BITD I would use a t-handle to push down and then reach in with the pick and just dig it out, piece of cake. Always did it by myself.

Reply to This

Then come on over and bake for me!! I have the Stainless dental picks and am about to go Marathon Man on these caps. I have a T phillips that fits the caps little center recess but can not hold it down and dig the clip out. I can't seem to get over or under the clip. I remember some Goki design idiots had air caps that once installed made it impossible to reach the clip.
I hate being weak.

Reply to This

Reply to This

RSS

About

Craig Knight Craig Knight created this Ning Network.

Forum

jack thompson

Mister Know it All. 116 Replies

Started by jack thompson. Last reply by Rick Oestricher 1 minute ago.

Ken Walden

KING OF THE ANTHILL '09 14 Replies

Started by Ken Walden. Last reply by lindsay harper Nov 22.

Albert Newmann

Rick Peterson: Here's your Sprocket Website!

Started by Albert Newmann Nov 21.

Latest Activity

While I may not know Jack's doodoo, I am familar with grammar.
1 minute ago
EXACTLY !!!! "Poor Thang's" story is just one more example of the misery and tragedy that befalls any devotee of the evil rotary valve design!
1 hour ago
Mike likes to ride occasionally, did i mention he brought Tvrc back from less than ten payed members to closee to 100. Was it his Bar BQ. And then Ken and Craig take the reins and beef it to over 100 close to 125. When ya meet any of these three s...
3 hours ago
Dear Mister Edwards, Rick Oestricher dont know JS. I recommend you gear the sach tall use a little bitty sprocket and never shift past first. that eliminates your tranny problems. Regards MKA
8 hours ago
David, This is not exactly what you're looking for but I am selling my 88 CR250. It is in immaculate condition with very low hours. I purchased it from the original owner in California (have original title). He could ride the DOS XX class? Asking...
11 hours ago
This was my dads bike he let me ride cause I had sold my Mini-Enduro and was saving up for a Yam MX100. We had to do a bore job on it and there was this guy in the nieghborhood that raced short track and he polished the ports and that bike was fas...
17 hours ago
Mr. KIA, Let me assist. The neutral-ectomy is properly performed by twisting and then pulling sharply up on the Sachs-engined device's gas cap making sure to carefully toss the remaining motorcycle in a garbage can and sliding an Elsinore in its p...
22 hours ago
Martin Brazil added a video
23 hours ago
Dear MKA, trying to uncover the true facts on my Sachs Shifting adjustments. I have looked in the the transmission and found 347 extra neutrals. Do you (seriously!) have the magic formula for correct adjustment of the the shifting mechanism. If a...
yesterday
We got a new kart and I was assigned the task of finding the roll over limit. Given our budget I couldn't afford the proper electronic equipment so I had to devise a simple base line to work off of. Knowing the scientific principles of basic fluid...
yesterday
Paul Burnett added a photo
yesterday
And I hear he is a great Mohel, on the side ;)
yesterday
Yeah !!! One dead Taco is a good start.
yesterday
My compliments to the chef!
yesterday
Martin Brazil and Leland Rooney are now friends
yesterday
Did this photographer get too close to a Bultaco? Is this picture the last thing he ever saw ?? Dirt bikers are protective of their stuff.
yesterday
JT...., I got yer HONCHO !!!!!!
yesterday
to be used with H2O only!
yesterday
Sure no problem im widely recognized as MKA
yesterday
Jack it needs a tad of work !!
yesterday

© 2009   Created by Craig Knight on Ning.   Create a Ning Network!

Badges  |  Report an Issue  |  Privacy  |  Terms of Service

Sign in to chat!